Five Cylinder Downpipe Audi RS3 8V TT RS 8S EA855 2.5L Turbo Catless Heat Shielded 76mm for 2015-2020 Models

The 8V / 8S Audi RS3 / TT RS is a car that rewards a properly engineered front pipe. Its EA855 2.5L turbo inline five engine produces 400 HP from the factory, and the original downpipe is built around cost, weight and noise targets rather than gas flow. Replacing it with a mandrel bent 76mm section removes the sharp restriction immediately after the turbine outlet, which lowers back pressure, sharpens throttle response and releases the exhaust note that the factory system holds back. This part is produced in house at our own workshop, jig welded on a dedicated 8V fixture, and inspected before it leaves the factory. It is supplied as a direct replacement for the original front pipe and reuses the factory gasket, clamps and hanger isolators.

The five cylinder engine has a distinctive firing order and a single turbo outlet, and the 8V and 8S cars share the engine but not the tunnel. This pipe is dedicated to the 8V RS3 and 8S TT RS: the downpipe does not transfer to the 8Y car, because the later platform uses a different subframe and a different sensor layout. Customers frequently ask for this specific split, so we keep separate tooling for each. The five cylinder sound is the main reason owners buy this pipe, and the wall thickness is chosen to keep the tone deep rather than harsh. An optional resonator sleeve can be welded in for customers who use the car daily and want to reduce drone at motorway speed.

• Direct 8V Fitment: Flange geometry and hanger positions are copied from the original part on a dedicated jig, so the pipe seats on the factory studs without slotting, bending or welding on the car for 2015-2020 vehicles.
• GPF on later builds: The emission layout is matched to this platform: oxygen sensor bosses sit at factory depth and angle, and the gpf aware design keeps the engine management free of pressure related faults after installation.
• 304L Stainless Construction: We use 1.5mm wall 304L stainless tube throughout, TIG welded with argon back purging on every joint so the inner weld bead stays clean and does not become a crack initiation point.
• Catted or Catless Options: Order the same pipe with a 200-cell or 300-cell high flow metallic substrate, or in a straight through catless version for competition use, without changing the external dimensions of the part.
• 76mm Mandrel Bent Routing: The main tube is mandrel bent rather than press bent, which keeps the internal diameter constant through every bend and avoids the wall thinning that chokes flow on cheaper parts.
• Integrated Heat Management: An optional stainless thermal barrier with locking tie wire is fitted to the hot side, reducing radiant heat into the wiring loom, the intake tract and the bulkhead during repeated full load runs.
• Hardware and Gasket Kit: Each set ships with new gaskets, correct grade studs and nuts, and a fitting note, so a workshop can complete the job with standard tools in a single lift.

This downpipe is intended for Audi RS3 / TT RS owners who want a measurable change in response and sound without rebuilding the whole exhaust. It suits stage one and stage two software upgrades, track day cars, and daily drivers whose owners simply want the engine to breathe properly. Typical buyers are performance workshops, tuning studios, exhaust retailers and enthusiast owners who service their own cars. Because the part is a direct replacement, the rear section, the valve control and the original tips remain untouched, which keeps the installation reversible. For markets with annual inspections we recommend the catted version, and for competition cars the catless version gives the shortest and least restrictive path from the turbine to the rear section.

Ordering is straightforward: confirm the model year and the drivetrain of the Audi RS3 / TT RS, choose catless or catted, and we will ship from stock where the configuration is available. Because we manufacture in house we can also run small batches with a specific substrate, a different resonator or a custom hanger for a particular market, and we keep tooling for every platform listed in this catalogue so repeat orders stay identical to the first shipment.

Every set is packed one piece per carton with foam corner protection and a desiccant sachet, then closed in an export grade corrugated box with the model number printed on the outside. Palletising is available for container orders. Before packing we check flange flatness, bore consistency, weld penetration and hanger alignment, and we keep a photo record of each batch. Our workshop runs a twelve month warranty against cracking and weld failure under normal use, and we support our distributors with fitting drawings, dimensional data and photography for their own catalogues. Sample orders are welcome so a workshop can verify fitment on a real car before committing to stock, and we can produce private label packaging on request.